How Much ???

[ruazfast]

Ok I need your help, I have read several times to put thin layers of polish, wax etc... but how do you know what is to thin or is there such a thing?. I'm not sure however I don't believe it would be good to go to thin either. Let me know what you think please :?

[PhaRO]

Thin and well covered is what I strive for. I know you can layer some products but I think there is a limit to how thick a layer can be built. I'd imagine just the friction of application would remove a lot of the previous layers. Since you are wiping most of it off, anything thicker than what adheres to the paint is enough. Just how I look at it though :)

[jaybs95]

I apply my LSP as thin as possible. I believe that putting it on thick doesn't help, because anything that isn't adhereing/bonding to the surface is being wiped off, it will also make it harder to wipe off. I will put on multiple layers to ensure that I have total coverage on the surface.
A small amount of of the previous layer of will be removed to to the friction caused by the application and removal to the next layer, but the goal is complete coverage.

There is also the topic of diminishing return and how long it takes for a wax to cure, but that is another topic...

"J"

[awd330]

The "proper" amount of product to use will vary depending upon the product itself as well as the method of application. Generally speaking, waxes and sealants should be applied so thinly that you can just barely see that there is something on the surface of the paint. Light polishes can usually be applied in more moderate amounts, while heavy polishes are often applied in somewhat generous amounts.

If you have to "work" a product, you will normally need to use more product than you would if just "applying" a product. Using a machine will also normally spread a product further than when using hand application. When considering hand applicators, cotton terry and microfiber covered applicators will absorb more product that most foam applicators.

If you have questions about specific products and methods of application, post them here and we will all try to help answer them.

[ruazfast]

Thanks everyone, as yes I have heard so much about putting to much that I am trying hard not to do that. I am mostly using a PC. I have not rec'd my PB product yet, I think they will be here next week. So what I believe you are telling me is if the product is more like a cleaner / swirl remover etc where you are trying to remove something then apply a little thicker, however if it is something to protect / wax / seal etc then apply thinner coat.
Thanks again for your help as I like this Forum since it is smaller then some and I feel more comfortable asking. As the bigger forums are great for info however this one kinda of reminds me of a Mom & Pop store if you know what I mean. :wink:

[awd330]

Yes, you seem to have grasped the general rules of thumb regarding how much of each product to use. As always, there are exceptions to the rule so be sure to post more questions as you get ready to use each of your products.

Since you mentioned Poorboy's, I can give you an example of an exception to the rule for this line: Professional Polish should be used in very, very, very small amounts even though most polishes should be used in moderate amounts. Several drops of Pro Polish at a time will most likely be enough to do the job. Using this product in moderate amounts will produce unsatisfactory results (smears).

I agree that this forum can be far less intimidating than some of the bigger ones. You won't have any demeaning or impersonal attitudes to contend with here. On the other hand, you may be missing some pieces of information that could be obtained from larger populations samples. For a newbie, you could try just reading/searching (lurking) on the larger boards and then posting your specific questions here. That should give you the best of both worlds. :)

[ruazfast]

[quote="awd330"]

On the other hand, you may be missing some pieces of information that could be obtained from larger populations samples.For a newbie, you could just reading/searching (lurking) on the larger boards and then posting your specific questions here. That should give you the best of both worlds.

Haha yes that is what I have been doing, kind of like cheating. :lol: :lol:

[Mirrored_Images]

Generally speaking, waxes and sealants should be applied so thinly that you can just barely see that there is something on the surface of the paint.

Excellent answer!

[Bob]

Generally speaking, waxes and sealants should be applied so thinly that you can just barely see that there is something on the surface of the paint.
Excellent answer!
Yeah, I helped on a Silver Magnum a couple weeks ago and the owner and I could not tell where we already put the product and where we already too it off. :lol: Looked great when it was done though. We used Natty's.